Glowforge · xTool P2 / S1 · OmTech CO2 · LightBurn

Laser-Cut Rhinestone Stencil SVG with Kerf Compensation

Laser beams vaporize material along the cut path, enlarging every hole by your beam kerf. Calculate your exact pre-kerf SVG hole diameter—such as a 2.9 mm drawn circle yields ~3.1 mm finished hole after kerf for SS10—and build rigid, reusable Mylar or cast-acrylic brushing jigs safely.

Interactive Laser Kerf & Pre-Kerf Hole Calculator

Because 0.10 to 0.22 mm laser beam kerf widens every hole, enter your desired physical hole size and measured laser kerf below to compute the exact SVG hole diameter to preload into our generator.

Drawn SVG Hole Setting (Target − Kerf)
2.9 mm SVG hole → 3.08 mm cut
Thermal Bridge Clearance
1.1 mm minimum web to prevent heat melt-through
Launch Maker with Kerf-Adjusted Hole

Laser Rhinestone Stencil Substrate & Pre-Kerf Reference Table

Substrate Laser Safety Thickness SS10 Drawn SVG Hole Min Web Gap Best Production Use
Polyester Mylar (BoPET) Safe (PVC-free polyester film) 10–14 mil (0.25–0.35 mm) 2.9 mm (yields ~3.08 mm) 1.1 mm Flexible sweep-in stencils taped to tray
Cast Acrylic Sheet Safe with standard exhaust 1.5 mm (1/16 in) 2.9 mm (CO2) / clear prohibited on blue diode 1.3 mm 1,000-cycle rigid production drop plates
Opaque Black/Orange Acrylic Safe (absorbs 455 nm diode beam) 1.5–2.0 mm 2.9–3.0 mm (fine diode spot ~0.10 mm) 1.2 mm xTool S1 / D1 Pro diode laser jigs
Resin-free Wood / Matte Board Safe (watch char dust) 1.0–1.5 mm 2.9 mm (wipe soot before brushing clear stones) 1.2 mm Quick prototype test plates
Polyurethane Laser Transfer Film Verify PVC-free SDS first 0.30–0.45 mm 2.9–3.0 mm 1.1 mm Specialty laser-rated stencil media
Standard PVC Sticky Flock / Vinyl NEVER LASER CUT Any Prohibited — use blade cutter instead N/A Cut on Cricut, Cameo, or ScanNCut only

Why Rigid Laser Jigs Beat Sticky Flock on High-Volume Runs

Flexible sticky flock excels for 1 to 25 shirts, but repeated hotfix tape lifts eventually pull fibers off the velvet surface. When a print shop runs 200 identical team warmups, laser cutting a 1.5 mm cast-acrylic drop plate or 14 mil Mylar stencil lets operators brush SS10 crystals into hard-walled pockets in under fifteen seconds per transfer with zero weeding waste. Just remember that stone depth matters on rigid plates: 1.5 mm acrylic sits slightly taller than an SS10 pavilion, so test carrier-tape tack reach on a small corner coupon before committing a full sheet.

Need blade-cut sticky flock specs instead? Compare our Cricut Design Space SVG guide or record pressing notes in the hotfix transfer planner.

Laser-Cut Rhinestone Stencil FAQ

Can I laser cut standard sticky rhinestone flock vinyl on a Glowforge or diode laser?

Do not laser cut unknown sticky flock or craft vinyl unless the manufacturer's SDS explicitly certifies it is PVC-free polyurethane or polyester. Many adhesive craft flocks contain polyvinyl chloride (PVC), which releases corrosive hydrogen chloride gas when lased—damaging optics, rails, and lungs. Use laser-safe Polyester Mylar (10 mil / 0.25 mm) or cast acrylic instead.

Why are my laser-cut SS10 holes too loose when I draw them at 3.1 mm?

Unlike a drag knife that pushes material aside, a CO2 or diode laser vaporizes a 0.10 to 0.22 mm laser beam kerf widens every hole around the perimeter. If your beam kerf is 0.18 mm, a drawn 2.9 mm circle yields ~3.08–3.1 mm finished opening—right in the sweet spot for SS10 stones.

How wide should bridges be on 10 mil Mylar or 1.5 mm acrylic rhinestone jigs?

Use a 1.1 mm minimum web to prevent heat melt-through between neighboring circles. Tighter 0.6–0.7 mm bridges accumulate heat when cutting dense honeycomb clusters, warping thin polyester film.

Which optimization order in LightBurn reduces heat distortion on dense stone grids?

In LightBurn's Optimization Settings, enable 'Cut inner shapes first' and 'Reduceger heat / Order by priority or scattered passes' with air assist running, so adjacent holes do not absorb back-to-back thermal pulses.